Maxtor Panther P0-12S and P1-17S 1.2 and 1.7 Gig. SCSI drives Performance Specifications /-----------------------------------+----------+-----------\ * Capacity, Unformatted * P0-12S * P1-17S * * +----------#-----------# * Per drive (Mbytes) * 1,224 * 1,759 * * Per surface (Mbytes) * 81.6 * 92.6 * * Per track (Bytes) * * * * MINIMUM * 35,795 * 41,650 * * MAXIMUM * 51,858 * 60,095 * **Capacity Formatted (512 BPS) * * * * * * * * Per drive (Mbytes) * 1,051 * 1,503 * * Per surface (Mbytes) * 70.1 * 79.1 * * Per track (Bytes) * * * * MINIMUM * 30,720 * 35,840 * * MAXIMUM * 44,544 * 51,712 * * * * * * Transfer rate, Mbits/sec * * * * MINIMUM * 17.2 * 20.1 * * MAXIMUM * 24.9 * 28.9 * * * * * * Seek time, typical **Msec * * * * Average * 13 * 13 * * Track to Track * 2 * 2 * * Full Stroke * 26 * 26 * * Maximum * * * * Average * 15 * 15 * * Track to Track * 2.5 * 2.5 * * Full Stroke * 30 * 30 * +-----------------------------------+----------+-----------/ Functional Specifications /-------------------------------------------+-----------+-----------\ * * P0-12S * P1-17S * * +-----------#-----------# * Rotational speed (rpm)* * 3,600 * 3,600 * * Average Latency (Msec) * 8.33 * 8.33 * * recording density (bpi) * * * * MINIMUM * 30,814 * 36,013 * * MAXIMUM * 37,836 * 42,981 * * Flux Density (fci) * * * * MINIMUM * 23,111 * 27,009 * * MAXIMUM * 28,377 * 32,235 * * Track Density (tpi) * 14,50 * 14,98 * * Cylinders * 17,95 * 17,78 * * Sectors per track (512 Bytes per sector) * 60-87 * 70-101 * * Sectors (512 Bytes)** * 2,053,275 * 2,947,261 * * Data Heads * 15 * 19 * * Servo Heads * 1 * 1 * * Disks * 8 * 10 * * * * * * * * * +-------------------------------------------+-----------+-----------/ * Accurate to +/- .1% ** With Spares Environmental Specifications /--------------------+-------------------------+-------------------------\ * * Equipment Operating * Equpiment Non-Operating * * +-------------------------#-------------------------# *Ambient Temperature * 50° F to 122° F * -40° F to 140° F * * * 10° C to 50° C * -40°C to 60° C * * * * * *Maximum Temperature * 18°F/Hr (10° C/Hr) * 18°F/Hr (10° C/Hr) * *Gradient * Below Condensation * Below Condensation * * * * * *Relative Humidity *8% to 80% Non-condensing *8% to 80% Non-Condensing * * *with maximum gradient of *with maximum gradient of * * *10% per hour *10% per hour * * * * * *Altitude *-1,000ft to 10,000ft. *-1,000 ft to 40,000 ft * * *-305m to 3,048m *-305m to 12,192m * * * * * *Vibration, all Axes *5-25 Hz, 0.006 in. P-P *5-25, 0.006 in. P-P * *(inputs to frame *25-500 Hz, 0.2 G Peak *25-500 Hz, 0.2 G Peak * * of drive) *Acceleration. *Acceleration. * * * * * *Shock all Axes * * * *(inputs to frame *5G, with no physical *5G, with no physical * * of drive) *damage and no data *damage and no data * *11 msec Pulse Width,*Corruption, but with *Corruption, but with * *Half Sine Wave *Retries 2G, within error *Retries 2G, within error * * *rate specification *rate specification * * * * * *Noise *45 dba at 1 meter, * N/A * * *Typical * * * * * * *Air flow for Cooling*500 linear ft./min. * N/A * * *at -1,000 ft. to 10,000 * * * *ft. Altitude * * * * * * +--------------------+-------------------------+-------------------------/ ---------------------------------------------------------------------------- Maxtor Original Fabrication Panther SCSI ---------------------------------------------------------------------------- POWER /-----------------------------------+--------------------------+-----------\ * J1 (SCSI CONNECTOR) * * J3 * +-----------------------------------/ /--\ /--------\ +-----------# * *J6* * J2 * * * .. JP10 +--/ +--------/ * * .. JP11 JP5 .. * * JP6 .. .. JP3 * * /------\ * * .. JP4 * U1 * * * /---\ * * * * *U13* +------/ * * +---/ ..JP2 /------\ * +-\ .. JP9 /-------------\ * U2 * * * * * U7 * +------# * *J* JP8 .. * * * U3 * * *4* +-------------/ +------/ * * * * +-/ * * * * * * /---------------\ * * * J5 * * +----------------------------------------------------+---------------+-----/ /-------------+---------------------------------------------+--------------\ *JUMPER NUMBER* Description * Default * +-------------#---------------------------------------------#--------------# * JP 2 * IN= Write Protected OUT= Read and Write * OUT * +-------------#---------------------------------------------#--------------# * JP 5 * IN= Slave Sync. Termination * OUT * +-------------#---------------------------------------------#--------------# * JP 6 * IN= Master Sync. Termination * OUT * +-------------#---------------------------------------------#--------------# * JP10 * IN= Termination Power supplied by Host * OUT * +-------------#---------------------------------------------#--------------# * JP11 * IN= Termination Power supplied by Drive * IN * +-------------+---------------------------------------------+--------------/ PC BOARD /--------------\ /-----------------------------------------------------------# J3 * +---------------------+------+------------+--------------+--+--------------/ * o o * Pin 9 *o o o o o * Pin 1 * o o * Pin 10 *o o o o o * Pin 2 +------/ +--------------/ J6 J2 J2 PINS : 1 & 2: Remote LED 3 & 4: Parity Enable=OFF, Disable=ON 5 & 6: MSB Drive ID. Value when jumpered = 4 7 & 8: Drive ID. Value = 2 9 & 10: LSB Drive ID. Value = 1 I.E. For ID 6, Pins 5-6 and 7-8 should be jumpered. For ID 0, 5-6, 7-8 and 9-10 should all be removed. All other jumpers should are factory set and should not be changed. ---------------------------------------------------------------------------- Maxtor Common Fabrication Panther SCSI ---------------------------------------------------------------------------- POWER /-----------------------------------+--------------------------+-----------\ * J1 (SCSI CONNECTOR) * /--\ /-------\ * J3 * +-----------------------------------/ *J6* * J2 * +-----------# * .. JP10 :+--/ : +-------/ * * .. JP11 JP6 JP13 .. JP5 * * /---\ /--\ * * JP3 *U13* *U9* /---\ * * +---/ +--/ *G1 * : JP1 * * +---/ : JP12* +-\ .. JP9 JP4 : /---\ /---\ /------\ * *J* *U22* *U15* * U 2 * * *4* +---/ +---/ +------/ * * * /---\ * * * .. JP8 *U4 * * +-/ +---# * * JP7 : *U5 * * * +---/ * * * * * * * * /-----------------\ * * * J5 * * +-----------------------------------------------------+-----------------+--/ /-------------+---------------------------------------------+--------------\ *JUMPER NUMBER* Description * Default * +-------------#---------------------------------------------#--------------# * JP 5 * IN= Slave Sync. Termination * OUT * +-------------#---------------------------------------------#--------------# * JP 6 * IN= Master Sync. Termination * OUT * +-------------#---------------------------------------------#--------------# * JP 10 * IN= Termination Power supplied by host * OUT * +-------------#---------------------------------------------#--------------# * JP 11 * IN= Termination Power supplied by drive * IN * +-------------#---------------------------------------------#--------------# * JP 13 * IN= Parity Disabled, OUT= Parity Enabled * OUT * +-------------+---------------------------------------------+--------------/ PC BOARD /--------------\ /-----------------------------------------------------------# J3 * +-----------------+------+-------------+---------------+----+--------------/ * o o * Pin 2 * o o o o o * Pin 10 * o o * Pin 1 * o o o o o * Pin 9 +------/ +---------------/ J6 J2 J2 Pins : 1 & 2: MSB Drive ID. Value when jumpered = 4 3 & 4: Drive ID. Value = 2 5 & 6: LSB Drive ID. Value = 1 7 & 8: Write Protect. IN= Enabled OUT= Read/Write 9 & 10: Remote LED /----+-----\ *JP1 * JP12* +----#-----# *OUT * OUT * Start by ID Sequence *OUT * IN * Start Motor after 11-13 second delay *IN * OUT * Wait for Motor Start Command *IN * IN * Start motor when power is applied +----+-----/